andreasandClaude Sonnet 5
e8fa2e025f
Pure-bash SHA-1 derived CELLULAR_UUID (no uuidgen); skip keyfile if empty. Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01KqhjP7nud5gdBg25zCiRk9
54 lines
3.2 KiB
Plaintext
54 lines
3.2 KiB
Plaintext
# hosts/vanlink.conf.example — reference for /etc/vanlink.conf.
|
|
#
|
|
# Each host has hosts/<hostname>.conf (hostname -s) in this repo, and
|
|
# /etc/vanlink.conf is a symlink to it:
|
|
# sudo ln -sfn "$PWD/hosts/$(hostname -s).conf" /etc/vanlink.conf
|
|
# Plain KEY=value (it is sourced by bash). NO SECRETS — this file is in git.
|
|
# Validate without root: ./deploy.sh --check hosts/<hostname>.conf
|
|
# Find interface names with `ip -br link` (wired) / `iw dev` (wifi); USB IDs with lsusb.
|
|
|
|
# --- Interfaces -------------------------------------------------------------
|
|
WIFI_5G_IFACE=wlp1s0 # 5GHz AP radio (hostapd)
|
|
WIFI_2G_IFACE=wlx000000000000 # 2.4GHz AP radio (hostapd-2g)
|
|
LAN_IFACE=enp1s0 # wired LAN port, bridged into br0
|
|
STARLINK_IFACE=enp2s0 # Starlink uplink (NetworkManager WAN)
|
|
WIFI_WAN_IFACE=wlan0 # optional: Wi-Fi uplink (NetworkManager WAN); empty = none
|
|
ONBOARD_LAN_IFACE= # optional: extra onboard LAN port bridged into br0 (e.g. eth0); empty = none
|
|
|
|
# --- Access point -------------------------------------------------------------
|
|
AP_SSID_5G=VanLink # SSID of the 5GHz AP (hostapd.conf)
|
|
AP_SSID_2G=VanLink # SSID of the 2.4GHz AP (hostapd-2g.conf)
|
|
# Radio-specific lines for the 5GHz AP: hostapd lines separated by the two characters \n
|
|
# (the GNU sed used by `render` expands them to newlines). Keep it in single quotes, e.g.
|
|
# AP_5G_RADIO='ht_capab=[HT40+][SHORT-GI-20]\nvht_capab=[RXLDPC][SHORT-GI-80]'
|
|
AP_5G_RADIO='ht_capab=[HT20][SHORT-GI-20]'
|
|
|
|
# --- Addressing ---------------------------------------------------------------
|
|
GATEWAY_IP="10.42.9.1"
|
|
GATEWAY_PREFIX="24"
|
|
GATEWAY_NETWORK="10.42.9.0/24"
|
|
DHCP_RANGE_START="10.42.9.10"
|
|
DHCP_RANGE_END="10.42.9.254"
|
|
DNS_RESOLVERS="1.1.1.1 8.8.8.8"
|
|
|
|
# --- Hardware -----------------------------------------------------------------
|
|
MODEM_USB_VENDOR=2c7c # cellular modem USB vendor id
|
|
NVME_DEVICE= # only when ENABLE_NVME_WATCH=1, e.g. nvme0
|
|
NVME_FS_DEVICE= # only when ENABLE_NVME_WATCH=1, e.g. /dev/nvme0n1p2
|
|
|
|
# --- Backup (read by failover/sync-*-backup.sh; leave empty if unused) ----------
|
|
USB_BACKUP_ROOT_PART= # sync-usb-backup.sh: partition to mount, e.g. /dev/sda2
|
|
USB_BACKUP_MOUNT= # sync-usb-backup.sh: local mount point, or host:/path for NFS
|
|
SD_BACKUP_UUID= # sync-sd-backup.sh: filesystem UUID of the backup SD card
|
|
|
|
# --- Feature flags (0 or 1) ---------------------------------------------------
|
|
ENABLE_COCKPIT=0 # Cockpit "Van Router" plugin
|
|
ENABLE_LI3=0 # Li3 house-battery BLE -> MQTT service
|
|
ENABLE_NVME_WATCH=0 # NVMe timeout watchdog (needs an NVMe drive)
|
|
ENABLE_HA=0 # Home Assistant + ESPHome (podman quadlets)
|
|
ENABLE_FRIGATE=0 # Frigate NVR (podman quadlet)
|
|
ENABLE_NM_WAN=1 # NetworkManager owns the WANs (netplan, cellular profile) via --apply-network
|
|
|
|
CELLULAR_CONN_NAME=Koodo # NM name of the cellular connection (also used by van-failover); needed with ENABLE_NM_WAN=1 when a cellular WAN is wanted
|
|
CELLULAR_APN=sp.koodo.com # cellular APN; needed with ENABLE_NM_WAN=1 when a cellular WAN is wanted (no APN = no cellular profile)
|