Updated hostapd.conf to run 5GHz AP on channel 149 with MT7925E (mt76 driver).
Now supports full 802.11ac (VHT) and 802.11ax (WiFi 6) capabilities.
Also fixed deploy.sh rendering issue that left unsubstituted placeholders in
network configs, causing Ethernet flaps. Configs are now properly deployed.
- hw_mode=a (5GHz), channel=149
- VHT and HE (WiFi 6) capabilities enabled
- Proper bridge configuration with gateway IP 10.42.1.1/24
- DHCP range 10.42.1.10-254 verified working
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
FriendlyElec R5C RTL8822CE WiFi chip does not support 5GHz AP mode.
Both wlan0 and wlan1 locked to 2.4GHz-only (mode 2) by firmware/driver.
Tested:
- Channel 149 (5GHz): fails with 'mode (2) not found'
- Channel 36 (5GHz): fails with 'mode (2) not found'
- Both wlan0 and wlan1: same limitation
- Regulatory domain persistence doesn't change mode
Solution: Configure hostapd for 2.4GHz (hw_mode=g, channel 6)
- VanLink2 now on wlan1, 2.4GHz channel 6
- VanLink2-2G still on wlan2, 2.4GHz channel 6
- Both working stably
R5C not recommended for 5GHz AP use; consider Pi 5 or other board
if 5GHz dual-band AP is required.
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
Problem: RTL8822CE driver caused kernel panic (watchdog hard LOCKUP) when
hostapd tried to use VHT 802.11ac with 80MHz channel width on channel 149.
Root cause: Driver/firmware instability with VHT capabilities on this chip.
Solution: Disable VHT, use HT40+ (802.11n) only.
- Removes ieee80211ac (VHT), ieee80211ax (802.11ax), and 80MHz channel width
- Keeps HT40+ with Short GI for reasonable performance
- Stable operation on channel 149 (5745 MHz)
This allows the 5GHz AP to start and beacon without lockup on R5C hardware.
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
Problem: R5C spontaneously rebooted due to hardware watchdog timeout
Cause 1: van-gps-owntracks in infinite restart loop (MQTT connect failed)
Cause 2: mosquitto only listening on localhost, so clients couldn't connect
Solution:
- Add restart limits to van-gps-owntracks and van-li3-battery services
(max 3 restarts per 5 minutes prevents infinite restart loops)
- Configure mosquitto to listen on all interfaces (0.0.0.0:1883)
- Deploy mosquitto listener config via deploy.sh
- Restart mosquitto during deploy to apply config changes
This prevents the system from hitting the 11-second hardware watchdog timeout
when services crash and systemd auto-restarts them indefinitely.
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
- deploy.conf templates interface names/USB IDs (@TOKEN@ substitution) across
ap/* configs so a dongle swap only needs deploy.conf edited, not the repo
configs themselves; drops ap/rtw88.conf (old 2.4GHz dongle retired for the
DWA-171, which needs no such power-save override).
- failover/van-wlan-watchdog: recovers wlan0 from NM's post-boot no-secrets
wedge (a boot-time supplicant race, not a real credential failure).
- deploy.sh: warn() collects dependency/config warnings (missing python3-gps,
python3-paho-mqtt, mobile-broadband-provider-info, grpcurl, gpsd; netplan
drift; unedited example configs) into /var/lib/vanlink/deploy-warnings.json,
rendered as an amber Cockpit card so they're visible without reading deploy
output.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Starlink's USB ethernet shares a hub with the rtw89 Wi-Fi adapter; when Starlink
flaps, the hub re-enumerates and tears the radio down, so hostapd loses its
interface and exits. Two stock defaults left the AP dark: Restart=on-failure
misses clean exits, and the 5-in-10s start limit makes systemd give up during a
re-enumeration storm.
- hostapd-restart.conf drop-in: Restart=always, RestartSec=5, StartLimitIntervalSec=0
so hostapd retries forever until the interface returns (verified: SIGKILL -> back
to state=ENABLED in ~7s).
- van-ap-watchdog daemon: backstop for the case systemd can't see (hostapd running
but radio wedged). Polls hostapd_cli status; restarts hostapd if the iface is
present but not ENABLED, waits it out if the iface is mid-re-enumeration.
- hostapd.conf: add ctrl_interface so the watchdog can read the real AP state.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Add a wired LAN port on the same 10.42.0.0/24 segment as VanLink WiFi by
bridging both into br0. The gateway IP, dnsmasq, and NAT move off the wlan name
onto br0; hostapd (not networkd) enslaves the wlan via bridge=br0, since a
station-mode wlan can't be bridged until it's in AP mode. NM leaves the wired
port unmanaged so networkd owns it. Failover/Starlink (enxd8ec5eeb3512)
untouched.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
andreasandClaude Sonnet 5
Andreas WredeandClaude Sonnet 5